NAVAIR 01-1A-505-2
006 03
TO 00-25-255-1
Page 2
TM 1-1500-323-24-2
NOTE
Support Equipment Required
As all NAVAIR connector and accessory
Part No./
Nomenclature
documents are transitioned to non-government
Type Designation
standards, the Society of Automotive Engineers
GS590
Die Set
(SAE) will become the preparing activity and
GS710
Die Set
the Navy will adopt the documents, and the
GS940
Die Set
drawing number prefix will change from MS
GS1010
Die Set
to AS. The main part number designation
GS1130
Die Set
remains the same, with the "M" prefix, such as
GS1250
Die Set
M81511/17-08. At times the entire item may be
GS1440
Die Set
superseded by another. There are many cases
GS1670
Die Set
where documents have been cancelled without
GS1920
Die Set
replacements, each case was reviewed and
GS2170
Die Set
some information has been retained in this
GS2420
Die Set
volume "for reference use only".
GS2670
Die Set
GS2920
Die Set
3. DESCRIPTION. MIL-DTL-83723 connectors utilize
HT-900B
Heat Gun
crimp type contacts that are inserted, released, and
M22520/1-01
Tool, Crimp, Frame
removed from the rear of connector.
M22520/1-02
Positioner
M22520-2-01
Tool, Crimp, Frame
4. The entire assembly process is performed at -rear of
M22520/2-02
Positioner
connector so that the possibility of damaging critical
M22520/7-01
Tool, Crimp, Terminal
interface of connector is greatly reduced. This rear
M22520/7-03
Positioner
release feature also permits the removal or installation
M81969/8-05
Tool, Insertion
of any number of contacts without uncoupling
M81969/8-06
Tool, Removal
connector.
M81969/8-07
Tool, Insertion
M81969/8-08
Tool, Removal
5. WIRE SEALING. Wire sealing is accomplished by
M81969/8-09
Tool, Insertion
use of a grommet seal designed to seal against outside
M81969/8-10
Tool, Removal
diameter of inserted wire. The outer diameter shall be
M81969/14-02
Tool, Insertion/Removal
within applicable size range.
M81969/14-03
Tool, Insertion/Removal
M81969/14-04
Tool, Insertion/Removal
6. MIL-DTL-83723 SERIES III.
M81969/30-05
Tool, Removal
M81969/30-06
Tool, Removal
7. MIL-DTL-83723 Series III connectors are bayonet
M81969/30-07
Tool, Removal
or thread coupled with rear release, rear removable,
13640
Tool, Crimp
crimp contacts. Hermetic connectors are available with
non-removable solder type contacts (Figure 1).
Materials Required
8. GROMMET SEALING PLUGS. The grommets of
Specification/
Nomenclature
environment resisting connectors are designed to accept
Part No.
sealing plugs in accordance with MS27488 to be used
S1009
Glue, Epoxy
where unwired contacts are placed. The connector
MIL-I-23053
Sleeving, Insulating,
when ordered as a unit will have sealing plugs enclosed
Heat-Shrinkable
to equal 15 percent of the number of contacts but not
MS3118 Series
Shrink Boot
less than one.
P-2740FR
Tape, Silicone Rubber
1. INTRODUCTION.
inserts have a resilient face with individual pin barriers
to seal against the hard face socket insert, The resilient
2. This Work Package (WP) pertains to connectors
interface seal provides individual contact seals in mated
condition between each contact and shell.
manufactured in accordance with MIL-DTL-83723
Series III.